Services

Six services, one contractor.

GIS delivers security programmes from the first risk assessment to long term support. Six services are provided under one contract and one point of responsibility, so that the customer deals with a single accountable contractor at every stage.

Six services, one contractor.
Consulting
01 / 06

Consulting

GIS advises governments, operators of critical infrastructure and armed forces on the protection of their sites, borders and airspace. Each engagement begins with an independent assessment of the threats the customer faces and of the measures already in place.

The assessment covers physical security, technology systems, operating procedures, staffing and training. It identifies vulnerabilities, ranks them by risk and estimates the cost and time required to address each of them.

The result is a written report and a technology roadmap that the customer can adopt in full or in stages. Where a customer already operates security systems, GIS reviews their condition and performance and recommends upgrades that protect the existing investment.

What the customer receives
  • ✓Needs analysis
  • ✓Threat and risk assessment
  • ✓Review of existing systems
  • ✓Technology roadmap
Design
02 / 06

Design

GIS designs complete security solutions for airports, seaports, border crossings, government facilities and military sites. Every design is prepared for the specific site and the specific risks identified during consulting.

Our engineers prepare the concept design, the detailed design, the technical specifications and the bills of quantities. Designs comply with the applicable international standards, including ICAO and IMO requirements where relevant, and with national regulations.

The customer reviews the design at each stage. Changes are agreed in writing before procurement begins, so that the delivered system corresponds exactly to the approved design.

What the customer receives
  • ✓Concept and detailed design
  • ✓Specifications and bills of quantities
  • ✓Compliance with international standards
  • ✓Design reviews with the customer
Integration
03 / 06

Integration

GIS is a full service systems integrator. We combine command and control, perimeter protection, access control, video surveillance, radar and communications into a single system that operators manage from one place.

Integration removes the gaps between separate systems. Alarms from sensors, cameras and radars are correlated in the command centre, so that operators receive verified information and can respond without delay.

GIS selects equipment from leading manufacturers on technical merit and is not bound to a single supplier. Interfaces are documented, and cyber security measures are applied to every networked component.

What the customer receives
  • ✓Command and control
  • ✓Perimeter and access control
  • ✓Cyber security
  • ✓Video surveillance and management
Project management and supervision
04 / 06

Project management and supervision

GIS manages each project from contract signature to final acceptance under one point of responsibility. A dedicated project manager reports to the customer throughout the project.

We establish the project schedule, the budget, the quality plan and the risk register at the outset, and report progress against them at agreed intervals. Equipment is tested at the factory before shipment so that faults are corrected before installation.

GIS manages all suppliers and subcontractors on behalf of the customer, including civil, electrical and mechanical works, and supervises their work on site to the approved standard.

What the customer receives
  • ✓Requirements capture
  • ✓Factory acceptance testing
  • ✓Supplier and subcontractor management
  • ✓Schedule and budget control
Installation
05 / 06

Installation

GIS technical teams install and commission systems on site or supervise installation by local contractors. Every step follows written procedures, so that the system performs as designed from the first day of operation.

Installation includes site preparation, the installation of equipment and cabling, configuration and commissioning. Each subsystem is tested individually and then as part of the complete system.

Site acceptance tests are carried out with the customer against the approved test procedures. The customer receives complete as built documentation, configuration records and operating manuals at handover.

What the customer receives
  • ✓Site preparation
  • ✓Installation and commissioning
  • ✓Site acceptance testing
  • ✓Handover documentation
Maintenance, support and training
06 / 06

Maintenance, support and training

GIS supports its systems throughout their service life. Customers choose the level of support that suits their operation, from scheduled preventive maintenance to permanent on site technical teams.

Preventive maintenance is carried out annually, twice a year or quarterly, according to the agreed plan. Qualified service staff provide technical support, and spare parts are held or procured to meet agreed response times.

GIS trains the customer's operators and technicians, provides training material, manuals and drawings, and certifies personnel where required. Systems are upgraded during their service life so that they continue to meet current standards.

What the customer receives
  • ✓Preventive maintenance
  • ✓Technical support
  • ✓Documentation services
  • ✓On site support and training

Supply, infrastructure and trained people, as one programme.

Request a consultation